Skip to content

Paint Calculator

Last updated

Your room

Enter the room size, doors, windows and coats. Doors count as 20 sq ft (0.9 × 2.1 m), windows 15 sq ft (1.2 × 1.2 m).

Room

Units

Paint

Coats

Use the figure on your can. Use less for new drywall, texture or rough surfaces.

Use the figure on your tin.

Results update as you type

—

Enter your room size, doors, windows and number of coats, and this paint calculator tells you how many gallons or litres of paint to buy for the walls – and the ceiling if you are painting it too.

How to calculate how much paint you need

  1. Add the lengths of all the walls (the room's perimeter) and multiply by the wall height.
  2. Subtract each door (a standard interior door is about 20 sq ft / 1.9 m²) and window (about 15 sq ft / 1.4 m² for a 3 × 5 ft window).
  3. Multiply the paintable area by the number of coats.
  4. Divide by the coverage on your paint can – often around 350–400 sq ft per US gallon or 10–12 m² per litre for one coat on a smooth surface.
  5. Round up to the cans you can buy.

Example: a 12 × 14 ft bedroom with 8 ft ceilings. Walls = 2 × (12 + 14) × 8 = 416 sq ft. Subtract one door (20 sq ft) and two windows (2 × 15 = 30 sq ft): 366 sq ft. Two coats: 732 sq ft. At 350 sq ft per gallon, you need 2.09 gallons – buy two gallons and one quart rather than three gallons. The ceiling (168 sq ft) adds about 1.0 gallons for two coats.

Metric example: a 4 × 3.5 m room with 2.5 m walls has 37.5 m² of wall. Less a door (0.9 × 2.1 m) and a window (1.2 × 1.2 m) leaves 34.2 m². Two coats at 12 m² per litre need 5.7 litres – a 5 L tin plus a 1 L tin.

Paint coverage: how far a gallon goes

Table of typical paint coverage: 350 to 400 square feet per gallon on smooth walls, less on new drywall, textured and rough exterior surfaces
Typical ranges. The coverage printed on your can is the best figure to use.

Coverage drops on porous or textured surfaces because they absorb and trap more paint. Rollers with a thick nap, spraying (overspray) and dark-to-light colour changes all increase how much you use. When in doubt, enter a lower coverage figure – leftover paint is useful for touch-ups.

How many coats of paint do you need?

SituationCoatsNotes
Same or similar colour, good existing paint1–2Two coats usually give a more even finish
Noticeable colour change2Plus primer for big changes
Dark to light, or bright reds/yellows2–3A tinted primer reduces coats
New drywall or bare plasterPrimer + 2Mist coat or drywall primer first
Patched wallsSpot-prime + 2Prevents shiny 'flashing' patches

Do you need primer?

Primer seals porous surfaces and helps topcoats stick and cover evenly. Use it on new drywall and plaster, bare wood, stains (water marks, smoke), glossy surfaces and big colour changes. Primer usually covers a similar area per gallon to paint, so the calculator adds one primer coat over the same area when you tick the box. 'Paint and primer in one' products can replace a separate primer on sound, previously painted walls, but not on bare or stained surfaces.

Doors, trim and ceilings

  • A standard interior door is about 20 sq ft per side; one quart (about 0.95 L) usually covers several door sides with two coats.
  • Baseboards, door frames and window trim need much less paint than walls – a quart of trim paint often covers a typical room.
  • Ceilings are usually painted in a flat white made for ceilings; measure length × width.
  • Paint the ceiling first, then walls, then trim.

Choosing a finish

Sheen affects how washable the wall is and how much it shows flaws. Flat or matte hides imperfections and suits ceilings and low-traffic rooms. Eggshell and satin are easier to clean and common in living areas and bedrooms. Semi-gloss and gloss are hard-wearing and used on trim, doors, kitchens and bathrooms. The sheen does not change how much paint you need very much – coverage depends more on the surface and colour.

Safety and preparation

Ventilate the room while painting and drying. Homes built before 1978 may have lead-based paint; sanding or scraping it can create hazardous dust, so test first and follow EPA lead-safe practices. Fill holes, sand glossy patches lightly, clean grease off kitchen walls and tape edges before you start – good preparation often matters more to the result than the paint itself.

Exterior paint: how much do you need?

For the outside of a house, measure the perimeter and multiply by the wall height to the eaves. For each gable end (the triangle under a pitched roof), add width × gable height ÷ 2. Subtract large openings such as garage doors. Rough siding, stucco and brick absorb more paint, so use a lower coverage figure – often 150–250 sq ft per gallon on the first coat. Example: a house with a 140 ft perimeter and 10 ft walls has about 1,400 sq ft of wall, plus two 30 ft wide gables 8 ft high (2 × 120 = 240 sq ft): 1,640 sq ft. Two coats at 300 sq ft per gallon need about 11 gallons – a 5-gallon bucket twice plus a gallon.

Gallon, quart or 5-gallon bucket?

ContainerUS volumeCovers one coat (at 350 sq ft/gal)
Quart0.25 gal (0.95 L)≈ 87 sq ft
Gallon1 gal (3.79 L)≈ 350 sq ft
5-gallon bucket5 gal (18.9 L)≈ 1,750 sq ft
Metric tins1 L / 2.5 L / 5 L / 10 L≈ 10 / 25 / 50 / 100 m² at 10 m²/L

Buying the right mix of containers saves money: if you need 2.1 gallons, two gallons and a quart are cheaper than three gallons. For large rooms or whole-house projects, a 5-gallon bucket is usually the best value and keeps the colour consistent – if you buy several cans of a custom colour, mix them together ('boxing') before you start so there is no slight colour difference between walls.

How long does paint take to dry between coats?

Water-based (latex/acrylic) wall paint is often dry to the touch within an hour and ready for a second coat after about 2–4 hours; oil-based paints can take 16–24 hours. Cool, humid weather slows drying. Always follow the recoat time on the can – painting too soon can cause peeling or a patchy finish.

Sources

  1. U.S. EPA – Lead in paint (homes built before 1978) — epa.gov/lead

Results are estimates for general information. Last reviewed: .

Zeeshan Nawaz

Written & built by

Zeeshan Nawaz

Calculator Developer · Tuff Search

Builds and tests Tuff Search calculators, turning published formulas and official sources into tools anyone can check.

FAQ

Frequently asked questions

Quick answers about the Paint Calculator.

With 8 ft walls, one door and one window, about 349 sq ft of wall – about 2.0 gallons for two coats at 350 sq ft per gallon.

Typically 350–400 sq ft for one coat on smooth, previously painted walls; less on textured or porous surfaces.

Multiply the wall's width by its height, subtract any doors or windows, multiply by the number of coats and divide by the coverage. A 12 × 8 ft wall needs about half a gallon for two coats.

Rarely for two coats. A typical bedroom needs about 2 gallons for the walls.

About 1 litre per 10–12 m² per coat on a smooth wall, so 2 coats need roughly 0.17–0.2 L per m².

Yes for large openings, but if you are painting the door and trim too, you can leave them in as a small buffer.

Still have a question? Email support@tuffsearch.com